Ameritemp AT500 500k BTU/H Dual Fuel {LP/NG} Direct Fired Make Up Air Heater
SKU:
AT500
$7,000.00
$5,350.00
$5,350.00
On Sale
per item
LOW COST INSTALLATION AND MAINTENANCE
Because of their low operating pressures, Ameritemp space heaters offer the most flexible, low cost installation: costly gas piping and expensive electrical connections are reduced, and installation is fast and simple. Ameritemp heaters, Models 500 and 1000, require no duct work and can be plugged into a standard 120 volt outlet. In addition, the one-man portability of these units keeps labor costs low.
DIRECT GAS FIRED TECHNOLOGY
ENERGY EFFICIENCY
DESIGN CERTIFIED
SAFETY AND APPROVALS
GAS FIRED HEATING EQUIPMENT
Because of their low operating pressures, Ameritemp space heaters offer the most flexible, low cost installation: costly gas piping and expensive electrical connections are reduced, and installation is fast and simple. Ameritemp heaters, Models 500 and 1000, require no duct work and can be plugged into a standard 120 volt outlet. In addition, the one-man portability of these units keeps labor costs low.
DIRECT GAS FIRED TECHNOLOGY
ENERGY EFFICIENCY
DESIGN CERTIFIED
SAFETY AND APPROVALS
GAS FIRED HEATING EQUIPMENT
Download Product Operation and Installation Manual
Download Wiring Diagram
Download Gas/Pipe Train Diagram
Download AT500 Safety Label
Designed to ANSI Z83.7-1990 Standard Construction Heater CSA APPROVED
Gases: Natural or Propane
Capacity: 500,000 Btu/h maximum
Orifice Size: 31 DMS (x125)
Maximum Supply Pressure: 10PSI {325-5A HP REGULATOR INCLUDED}
Blower: 4,650 CFM; 1/2 HP; 1.5 In W.C.S.P.
Electrical Rating:
120V 7 amps, Single Phase {20Amp Circuit Required}
Wire Sizing: Up to 100' 12ga.; 100-200' 10ga.
Minimum Temperature Rating: Minus 40 degrees F
Gas Supply: Inlet Pressure Manifold Pressure
Max PSI Min PSI W.C.
Propane 10 lbs. 1 psi 1.5”
Natural Gas 10 lbs. 1 psi 3.5”
MAX. FUEL USAGE PER HOUR: 5.46 GAL LP & VP OR 5 THERMS NG
Inlet Connection:
Model AT500 (Nat/Vap Propane) 1” FNPT
Weight (approximate): 135 lbs. 42"L x 20"W x 30"H
The heater is designed for indoor or outdoor installation in a horizontal position. Allow the
following clearances from any combustible material or fuel containers.
Front Outlet: 10 feet Sides: 2 feet
Intake: 1.5 feet Top: 4 feet
Also make sure that no flammable vapors are present in the space where the heaters is being used.
The heater must be at least 6 ft. from any LP-Gas container, and not directed toward any LP-Gas container with in 20 ft.
Minimum Tank Size Outdoor Temperature
500 Gal. Above +25˚F
1 x 1000 Gal. +25˚F to + 10˚ F
1 x 1000 Gal. Below +10˚F
Download Wiring Diagram
Download Gas/Pipe Train Diagram
Download AT500 Safety Label
Designed to ANSI Z83.7-1990 Standard Construction Heater CSA APPROVED
Gases: Natural or Propane
Capacity: 500,000 Btu/h maximum
Orifice Size: 31 DMS (x125)
Maximum Supply Pressure: 10PSI {325-5A HP REGULATOR INCLUDED}
Blower: 4,650 CFM; 1/2 HP; 1.5 In W.C.S.P.
Electrical Rating:
120V 7 amps, Single Phase {20Amp Circuit Required}
Wire Sizing: Up to 100' 12ga.; 100-200' 10ga.
Minimum Temperature Rating: Minus 40 degrees F
Gas Supply: Inlet Pressure Manifold Pressure
Max PSI Min PSI W.C.
Propane 10 lbs. 1 psi 1.5”
Natural Gas 10 lbs. 1 psi 3.5”
MAX. FUEL USAGE PER HOUR: 5.46 GAL LP & VP OR 5 THERMS NG
Inlet Connection:
Model AT500 (Nat/Vap Propane) 1” FNPT
Weight (approximate): 135 lbs. 42"L x 20"W x 30"H
The heater is designed for indoor or outdoor installation in a horizontal position. Allow the
following clearances from any combustible material or fuel containers.
Front Outlet: 10 feet Sides: 2 feet
Intake: 1.5 feet Top: 4 feet
Also make sure that no flammable vapors are present in the space where the heaters is being used.
The heater must be at least 6 ft. from any LP-Gas container, and not directed toward any LP-Gas container with in 20 ft.
Minimum Tank Size Outdoor Temperature
500 Gal. Above +25˚F
1 x 1000 Gal. +25˚F to + 10˚ F
1 x 1000 Gal. Below +10˚F
