- Temporary Portable Mobile Industrial Commercial and Construction Heaters
- >
- Portable Electric Salamanders & Space Heaters
- >
- Portable Electric Salamander Heaters
- >
- Chromalox Portable Electric Salamander Blower Heaters
- >
- Chromalox SDRA Portable High Temperature Electric Blower Heaters
- >
- Chromalox SDRA-60-93 Portable High Temperature Blower Heater 60.0KW 600V 3Ph PCN 295734
Chromalox SDRA-60-93 Portable High Temperature Blower Heater 60.0KW 600V 3Ph PCN 295734
SKU:
SDRA-60-93
$10,859.00
$7,818.48
$7,818.48
On Sale
Unavailable
per item
SDRA Portable High Temperature Blower Heater
- 30, 48 and 60kW
- 102,360 to 204,720 BTUH
- 480 or 600 Volts, Three Phase
- Built-in Controls
- High Temperature Heater
- Use with Flexible Duct
Specifications:
Dimensions: (WxLxH) 30.25x44x38.5
Stock Status: S = stock NS = non-stock
|
The Chromalox SDRA SuperDragon is a rugged, self contained, mobile electric blower heater that can be used with or without optional inlet or outlet 20” diameter flexible duct. The SDRA units can be used for comfort heating or process heating temperatures to 180˚F, and can be located in an ambient of up to 130˚F. The SDRA includes a fan only switch, that allows the unit to be used to recirculate room air, supply fresh air source, or capture fume exhaust. The SDRA heaters provide for easily adjustable airflow for a wide variety of applications including flexible ducting up to 165 feet in length. Each unit includes two thermostats to enable the operator to set the maximum inlet and outlet temperatures, magnetic contactor(s), a 120 volt control transformer, power on pilot lights and a high limit cutout to protect the heater against unintended low air flow conditions. The SDRA can be left unattended without the threat of fire or by-product of combustion from fuel fired heaters. The bright red polyester powder coated heater can be easily moved because of two 10” diameter pneumatic wheels on the outlet and a 4” lockable swivel castor on the inlet.
Applications:
- Aircraft Cabin Heating - Plant Maintenance - Construction Sites - Curing Plaster And Concrete - Warming Workers - Drying Out After Floods - Insect Control - Thawing Frozen Pipes For best results, use in an enclosed area with ceiling heights below 15 feet. |
Advantages:
- No Fumes Or Annoying Smell - Safer, No Open Flame - Safe To Operate In Unattended Areas - No Moisture And Fumes Added To The Air - Burning Oil And Gas Fuels Adds Moisture And Fumes To The Air - Minimum Maintenance - No Fuel To Store - Long Horizontal Air Throw - Easy Installation - Fan Only For Summer Cooling - Long Life Industrial Finned Tubular Heating Elements - High Limit Thermal Cut-out Switch |
Chromalox SDRA Construction:
Heating Section:
A structural frame consisting of 2 spun steel rings and formed steel channels support a 20 gauge steel cylinder phosphate coated for corrosion resistance and finished in red polyester powder coat paint. The cylinder contains patented metal sheath Fintube® heating elements that include industrial grade .475” diameter steel sheath tubular heaters with furnace brazed steel fins for maximum heat transfer. The elements are firmly attached to a robust steel assembly with steel bulkhead threaded fittings.
Fan Section:
The fan assembly includes a 16” tubeaxial fan designed for industrial use and includes a streamlined belt tunnel that isolates the motor, drives and bearings from the air stream. The fan blades are precision balanced made with spark resistant aluminum and includes permanently lubricated ball bearings. Safety belt guards are supplied to protect operating personnel from harm. The drip proof motor is rated 1hp, 3 phase 1,725 rpm and operates on line voltage. Fan speed can be varied from 1,500 to 2,300 RPM for various air flows by use of adjustable pulleys.
Controls:
Two adjustable thermostats (60 to 180˚F) are located on the heater cylinder to allow the inlet and outlet temperatures to be adjustable for single pass heating or recirculated air temperature control. The power is switched by magnetic contactor(s) which are located in a gasketed NEMA 4 enclosure along with the motor starter, control voltage transformer and heater power fusing. A fan only toggle switch and pilot lights for power and heater are also located in the enclosure.
Safety Guards:
Front and rear grills are 10 gauge, finished in black polyester powder coat paint and are designed to meet OSHA requirements.
Heating Section:
A structural frame consisting of 2 spun steel rings and formed steel channels support a 20 gauge steel cylinder phosphate coated for corrosion resistance and finished in red polyester powder coat paint. The cylinder contains patented metal sheath Fintube® heating elements that include industrial grade .475” diameter steel sheath tubular heaters with furnace brazed steel fins for maximum heat transfer. The elements are firmly attached to a robust steel assembly with steel bulkhead threaded fittings.
Fan Section:
The fan assembly includes a 16” tubeaxial fan designed for industrial use and includes a streamlined belt tunnel that isolates the motor, drives and bearings from the air stream. The fan blades are precision balanced made with spark resistant aluminum and includes permanently lubricated ball bearings. Safety belt guards are supplied to protect operating personnel from harm. The drip proof motor is rated 1hp, 3 phase 1,725 rpm and operates on line voltage. Fan speed can be varied from 1,500 to 2,300 RPM for various air flows by use of adjustable pulleys.
Controls:
Two adjustable thermostats (60 to 180˚F) are located on the heater cylinder to allow the inlet and outlet temperatures to be adjustable for single pass heating or recirculated air temperature control. The power is switched by magnetic contactor(s) which are located in a gasketed NEMA 4 enclosure along with the motor starter, control voltage transformer and heater power fusing. A fan only toggle switch and pilot lights for power and heater are also located in the enclosure.
Safety Guards:
Front and rear grills are 10 gauge, finished in black polyester powder coat paint and are designed to meet OSHA requirements.